A light-emitting diode, usually called an LED (pronounced /ˌɛliːˈdiː/),is a semiconductor diode that emits incoherent narrow-spectrum light when electrically biased in the forward direction of the p-n junction, as in the common LED circuit. This effect is a form of electroluminescence.
A LED is usually a small area light source, often with optics added to the chip to shape its radiation pattern and assist in reflection.LEDs are often used as small indicator lights on electronic devices and increasingly in higher power applications such as flashlights and area lighting. The color of the emitted light depends on the composition and condition of the semiconducting material used, and can be infrared, visible, or ultraviolet. LEDs can also be used as a regular household light source. Besides lighting, interesting applications include sterilization of water and disinfection of devices.
Discovery and development
The first known report of a light-emitting solid-state diode was made in 1907 by the British experimenter H. J. Round of Marconi Labs. Russian Oleg Vladimirovich Losev independently created the first LED in the mid 1920s; his research, though distributed in Russian, German and British scientific journals, was ignored,and no practical use was made of the discovery for several decades. Rubin Braunstein of the Radio Corporation of America reported on infrared emission from gallium arsenide (GaAs) and other semiconductor alloys in 1955. Braunstein observed infrared emission generated by simple diode structures using GaSb, GaAs, InP, and Ge-Si alloys cooled by liquid nitrogen to 77 K. Experimenters at Texas Instruments, Bob Biard and Gary Pittman, found in 1961 that gallium arsenide gave off infrared radiation when electric current was applied. Biard and Pittman were able to establish the priority of their work and received the patent for the infrared light-emitting diode.
The first practical visible-spectrum (red) LED was developed by Nick Holonyak Jr. in 1962, then of the General Electric Company and later with the University of Illinois at Urbana-Champaign and is seen as the "father of the light-emitting diode".Holonyak's former graduate student, M. George Craford, invented in 1972 the first yellow LED and 10x brighter red and red-orange LEDs.
Shuji Nakamura of Nichia Corporation of Japan demonstrated the first high-brightness blue LED based on InGaN, borrowing on critical developments in GaN nucleation on sapphire substrates and the demonstration of p-type doping of GaN which were developed by I. Akasaki and H. Amano in Nagoya. In the 1995 Alberto Barbieri at the Cardiff University Laboratory (GB) investigated the Efficiency and Reliability of high-brightness LED demonstrating very high result by using a transparent contact made by indium tin oxide (ITO) on (AlGaInP/GaAs) LED. The existence of the blue LED and high efficiency quickly carried to the first white LED, which employed a Y3Al5O12:Ce, or "YAG", phosphor coating to mix yellow (down-converted) light with blue to produce light that appears white. Nakamura was awarded the 2006 Millennium Technology Prize for his invention.
Practical use
The first commercial LEDs were commonly used as replacements for incandescent indicators, and in seven-segment displays, first in expensive equipment such as laboratory and electronics test equipment, then later in such appliances as TVs, radios, telephones, calculators, and even watches. These red LEDs were bright enough only for use as indicators, as the light output was not enough to illuminate an area. Later, other colors became widely available and also appeared in appliances and equipment. As the LED materials technology became more advanced, the light output was increased, while maintaining the efficiency and the reliability to an acceptable level, causing LEDs to become bright enough to be used for illumination.
Most LEDs were made in the very common 5 mm T1³⁄₄ and 3 mm T1 packages, but with higher power, it has become increasingly necessary to shed excess heat in order to maintain reliability, so more complex packages adapted for efficient heat dissipation are becoming common. Packages for state-of-the-art high power LEDs bear little resemblance to early LEDs (see, for example, Philips Lumileds).
Physical principles:-
Like a normal diode, the LED consists of a chip of semiconducting material impregnated, or doped, with impurities to create a p-n junction. As in other diodes, current flows easily from the p-side, or anode, to the n-side, or cathode, but not in the reverse direction. Charge-carriers—electrons and holes—flow into the junction from electrodes with different voltages. When an electron meets a hole, it falls into a lower energy level, and releases energy in the form of a photon.
The wavelength of the light emitted, and therefore its color, depends on the band gap energy of the materials forming the p-n junction. In silicon or germanium diodes, the electrons and holes recombine by a non-radiative transition which produces no optical emission, because these are indirect band gap materials. The materials used for the LED have a direct band gap with energies corresponding to near-infrared, visible or near-ultraviolet light.
LED development began with infrared and red devices made with gallium arsenide. Advances in materials science have made possible the production of devices with ever-shorter wavelengths, producing light in a variety of colors.
LEDs are usually built on an n-type substrate, with an electrode attached to the p-type layer deposited on its surface. P-type substrates, while less common, occur as well. Many commercial LEDs, especially GaN/InGaN, also use sapphire substrate.
Light extraction
Substrates that are transparent to the emitted wavelength, and backed by a reflective layer, and light spreading layer, increase the LED efficiency. The refractive index of the package material should match the index of the semiconductor, otherwise the produced light gets partially reflected back into the semiconductor, where it may be absorbed and turned into additional heat, thus lowering the efficiency. This type of reflection also occurs at the surface of the package if the LED is coupled to a medium with a different refractive index such as a glass fiber or air. The refractive index of most LED semiconductors is quite high, so in almost all cases the LED is coupled into a much lower-index medium. The large index difference makes the reflection quite substantial (per the Fresnel coefficients), and this is usually one of the dominant causes of LED inefficiency. Often more than half of the emitted light is reflected back at the LED-package and package-air interfaces. The reflection is most commonly reduced by using a dome-shaped (half-sphere) package with the diode in the center so that the outgoing light rays strike the surface perpendicularly, at which angle the reflection is minimized. An anti-reflection coating may be added as well. The package may be cheap plastic, which may be colored, but this is only for cosmetic reasons or to improve the contrast ratio; the color of the packaging does not substantially affect the color of the light emitted. Other strategies for reducing the impact of the interface reflections include designing the LED to reabsorb and reemit the reflected light (called photon recycling) and manipulating the microscopic structure of the surface to reduce the reflectance, by introducing random roughness, creating programmed moth eye surface patterns. Recently Photonic crystal have also been used to minimize back-reflections.In December 2007, scientists at Glasgow University claimed to have found a way to make Light Emitting Diodes brighter and use less power than energy efficient light bulbs currently on the market by imprinting holes into billions of LEDs in a new and cost effective method using a process known as nanoimprint lithography.
Materials
Conventional LEDs are made from a variety of inorganic semiconductor materials, producing the following colors:
Aluminium gallium arsenide (AlGaAs) — red and infrared
Aluminium gallium phosphide (AlGaP) — green
Aluminium gallium indium phosphide (AlGaInP) — high-brightness orange-red, orange, yellow, and green
Gallium arsenide phosphide (GaAsP) — red, orange-red, orange, and yellow
Gallium phosphide (GaP) — red, yellow and green
Gallium nitride (GaN) — green, pure green (or emerald green), and blue also white (if it has an AlGaN Quantum Barrier)
Indium gallium nitride (InGaN) — 450–470 nm — near ultraviolet, bluish-green and blue
Silicon carbide (SiC) as substrate — blue
Silicon (Si) as substrate — blue (under development)
Sapphire (Al2O3) as substrate — blue
Zinc selenide (ZnSe) — blue
Diamond (C) — ultraviolet
Aluminium nitride (AlN), aluminium gallium nitride (AlGaN), aluminium gallium indium nitride (AlGaInN) — near to far ultraviolet (down to 210 nm)
With this wide variety of colors, arrays of multicolor LEDs can be designed to produce unconventional color patterns.
Subscribe to:
Post Comments (Atom)
2 comments:
Good day, sun shines!
There have been times of troubles when I didn't know about opportunities of getting high yields on investments. I was a dump and downright pessimistic person.
I have never thought that there weren't any need in big starting capital.
Now, I feel good, I begin take up real money.
It's all about how to select a proper companion who uses your funds in a right way - that is incorporate it in real deals, and shares the income with me.
You may ask, if there are such firms? I'm obliged to answer the truth, YES, there are. Please be informed of one of them:
http://theinvestblog.com [url=http://theinvestblog.com]Online Investment Blog[/url]
Hello There. I found your blog using msn. This is a very well written
article. I will be sure to bookmark it and come back to read
more of your useful information. Thanks for the post. I'll definitely comeback.
Look into my web-site travel
Post a Comment